
Intervene now on the DCUs that equip some Ford brand models.
Work to tune and repair on the Bosch DCU17PC43 unit with the new BENCH mode protocol for KESS3.
The Alientech team that deals with the Drivers update focused on the Continental SID310 and SID307 equipped on Mercedes-Benz, Infiniti, Renault and Nissan.
The ECUs involved are:
In addition to the standard maps useful to significantly increase the performance of these ECUs, we present some specific maps, which will lead you to even better results.
Any vehicles examples?
Continental SID307
Mercedes A Class(W176) 180d 109cv
Nissan Juke 1.5 DCi 109cv
Renault Kangoo 1.5 DCi 109cv
Renault Megane (III) 1.5 DCi 109cv
Continental SID310
Mercedes A Class (W176) 180d 115cv
Infiniti Q30 1500d 115cv
Renault Clio (IV) 1.5 DCi 110cv
Renault Megane (IV) 1.5 DCi 110cv
Renault Kadjar 1.5 DCi 110cv
Renault Master 2.3 DCi 130cv
Nissan Qashqai 1.5 DCi 110cv
Nissan Navara 2.3 Dci 160cv
On most modern Diesel engines, it is necessary to work on this map and disable the control of the torque calculation, made by the ECU to protect the engine and the gearbox components.
By setting this map to 0, it is possible to inhibit this control to avoid, while using the vehicle, annoying recovery or engine misfunctions.
This map allows to manage the exhaust gas temperature to protect the DPF and the turbocharger against possible overheating and consequent breakdown of these components.
It is a protection map that reduces the power, by putting the engine in protection mode once the ECU reads an excessive temperature from the sensor on the exhaust.
Generally, with the standard vehicle, this problem never occurs but, with tuned engine parameters – turbo pressure and fuel quantity – it will be necessary to raise the maximum permissible temperature threshold, to avoid recovery.
Note: the problem appears generally while driving long distances with medium or high revs and high engine load with long gears (5th or 6th gear), this because the more fuel is injected in the engine the more heat will be generated in the exhaust system.
The EGR valve is a component electronically controlled by the ECU that, by taking part of the combustion gases emitted by the engine in the exhaust, returns them after having cooled them properly through a heat exchanger, in the intake manifold. What is the point? Reduce carbon monoxide emissions (NOx) at exhaust.
The map in this case can be seen as an end-of-intervention threshold of the EGR valve: above a certain engine torque value, the valve will remain closed.
The exclusion of this valve leads advantages in terms of engine torque at low rpm and facilitates acceleration phases, also maintaining the car’s intake system cleaner – generally the combustion gases are re-used downstream of the turbocharger, if taken before the DPF and upstream if taken after the DPF.
On these engine management it is possible, through some specific maps, like the engine correction, to alter the way the ECU corrects the torque parameters according to determined conditions.
In this case, the map decreases the engine torque generated by the engine as the intake air temperature rises, to always keep the operating temperatures under control. The value present in the map is a factor multiplied by the torque value, consequently, if below 1 the engine torque will be reduced, if above 1 it will be increased. With a value of 1 the ECU will not make any change in the torque.
About Continental SID307 the maps are very similar and the latest updates were aimed precisely at inserting the maps already described for the SID310.
In the next few weeks, Drivers update on Bosch EDC17C84 equipped on Renault and Nissan vehicles. Any examples?
NISSAN
OPEL
RENAULT
DACIA
Dacia Dokker 1.5 DCi 90cv
FIAT
Fiat Talento 1.6 MJT 90cv e 1.6 MJT 145cv
Work to tune and repair on the Bosch DCU17PC43 unit with the new BENCH mode protocol for KESS3.
Even more possibilities for modification and customisation are available for Mercedes Benz.
Thanks to the latest KESS3 upgrade, you can work in BENCH mode on this ECU and enhance performance with the best solution on the market for reliability and efficiency.
A new release is now available for Alientech’s remapping software.
A new protocol for KESS3 allows you to work with total reliability on the ECUs that are equipped on Xylo, Nuvosport, Bolero, Imperio and Quanto turbo diesel, produced between 2011 and 2016.
Thanks to the two new OBD protocols available only on KESS3, you can work on these Delphi ECUs easily, quickly and effectively.
For thirty years, as a team, we’ve been developing, creating and producing the best tools and software for chiptuners and mechatronics.
We have evolved during these years of hard work. From a dynamic start-up we have become a multinational firm with offices and dealers all over the world.
P.IVA IT02007510023
Cap. Soc. € 10.329,14
Registro Produttori AEE IT10120000006984
Alientech Srl 2021 – © Alientech All rights reserved Privacy – Cookie – Terms of use – Legals
Alientech Srl Cap. Soc. € 10.329,14 P.IVA IT02007510023 Registro Produttori AEE IT10120000006984